| # SPDX-FileCopyrightText: The Eigen Authors | |
| # SPDX-License-Identifier: MPL-2.0 | |
| # The complement of find_package_version_range: without a rejection case, a | |
| # version file that accepted everything would pass that test. | |
| # | |
| # The non-range branch of cmake/Eigen3ConfigVersion.cmake.in accepts a package | |
| # whose version is at least the requested one and below the next major, so a | |
| # bare "3.4" spans >=3.4 to <4.0.0 rather than 3.4.z. Rejecting a request one | |
| # major above the installed package would hold under either reading, so the | |
| # cases below pin the implemented one: both bounds, plus -- whenever the | |
| # installed version leaves room to state it -- a minor below the installed one | |
| # that must still be accepted. | |
| bs_install_eigen() | |
| bs_eigen_package_version(major minor patch) | |
| if(major LESS 4) | |
| bs_fail("this scenario assumes Eigen's major version is at least 4, got ${major}") | |
| endif() | |
| # Upper bound: an earlier major must not answer, whatever its minor. | |
| bs_configure_expect_failure("consumer pinned to 3.4" "${BS_CONSUMER_DIR}/installed" | |
| "${WORK_DIR}/consumer-old" output | |
| "-DCMAKE_PREFIX_PATH=${BS_PREFIX}" | |
| "-DEIGEN_EXPECTED_PREFIX=${BS_PREFIX}" | |
| "-DEIGEN_VERSION_SPEC=3.4" | |
| ${BS_FIND_PACKAGE_ISOLATION}) | |
| if(NOT output MATCHES "Eigen3") | |
| bs_fail("configure failed for some reason other than the version check\n----\n${output}\n----") | |
| endif() | |
| math(EXPR too_new "${major}+1") | |
| bs_configure_expect_failure("consumer requiring ${too_new}" "${BS_CONSUMER_DIR}/installed" | |
| "${WORK_DIR}/consumer-new" output | |
| "-DCMAKE_PREFIX_PATH=${BS_PREFIX}" | |
| "-DEIGEN_EXPECTED_PREFIX=${BS_PREFIX}" | |
| "-DEIGEN_VERSION_SPEC=${too_new}" | |
| ${BS_FIND_PACKAGE_ISOLATION}) | |
| if(NOT output MATCHES "Eigen3") | |
| bs_fail("configure failed for some reason other than the version check\n----\n${output}\n----") | |
| endif() | |
| # Lower bound: a patch above the installed one is inside the same major and must | |
| # still be rejected, which a file that only compared majors would not do. | |
| math(EXPR next_patch "${patch}+1") | |
| bs_configure_expect_failure("consumer requiring ${major}.${minor}.${next_patch}" | |
| "${BS_CONSUMER_DIR}/installed" | |
| "${WORK_DIR}/consumer-patch" output | |
| "-DCMAKE_PREFIX_PATH=${BS_PREFIX}" | |
| "-DEIGEN_EXPECTED_PREFIX=${BS_PREFIX}" | |
| "-DEIGEN_VERSION_SPEC=${major}.${minor}.${next_patch}" | |
| ${BS_FIND_PACKAGE_ISOLATION}) | |
| if(NOT output MATCHES "Eigen3") | |
| bs_fail("configure failed for some reason other than the version check\n----\n${output}\n----") | |
| endif() | |
| # The case that separates ">=X.Y, <X+1.0.0" from "X.Y.z": an older minor of the | |
| # installed major must be accepted. Only statable once the release series has | |
| # moved past .0, so it is a control the scenario adds when it can rather than a | |
| # requirement on the version number. | |
| if(minor GREATER 0) | |
| math(EXPR previous_minor "${minor}-1") | |
| bs_configure("consumer requiring ${major}.${previous_minor}" "${BS_CONSUMER_DIR}/installed" | |
| "${WORK_DIR}/consumer-minor" | |
| "-DCMAKE_PREFIX_PATH=${BS_PREFIX}" | |
| "-DEIGEN_EXPECTED_PREFIX=${BS_PREFIX}" | |
| "-DEIGEN_VERSION_SPEC=${major}.${previous_minor}" | |
| ${BS_FIND_PACKAGE_ISOLATION}) | |
| bs_build_and_run_consumer("consumer requiring an older minor" "${WORK_DIR}/consumer-minor") | |
| endif() |